Website logo
⌘K
Hand Held Legend Wiki
Modding Tips
Electrolytic Re-Cap Guide
Soldering Iron Guide
Sensitive Touch Sensors
Power Switch Cleaning Guide
Removing Adhered Screens
Restore Your Original Gameboy Bumper Buttons To Factory
IPS Comparison Info
Identifying GBA 32/40 Pin
IPS LCD Dry Test
GBA SP | IPS LCD Dry Test
HHL Products
ProGCC V3
GC Pocket Adapter
GC Pocket Adapter +
Open Controller DevKit
Retro-C Cable Information
RetroGlow
ProGCC V2 and V1
Torx Screw Kits
Console Guides
Game Gear
Nintendo Switch
GameCube
Game Boy (DMG)
Game Boy Pocket
Game Boy Color
Game Boy Advance (AGB)
Game Boy Advance SP
Nintendo DS
Mod Install Guides
Nintendo Switch
Nintendo N64
Game Gear
GameCube
Game Boy (DMG)
Game Boy Pocket/Light
Game Boy Color
Game Boy Advance (AGB)
Game Boy Advance SP
Atari Lynx
Sega Saturn
WonderSwan
Product Usage Guides
EZ Flash Upgrade Guide
Writing A Rom To A Flash Cart
🧃 CleanJuice Modules
Game Boy Color
Troubleshooting
🔉Audio
IPS Troubleshooting Guide
⚡EZ-Flash Omega Troubleshoot
🔋 Power Switch Is Too Small
Developer Center
OpenJoyPad HID USB Specification
USB Product IDs Used
Nintendo Switch
Affiliate Guidelines
Docs powered by Archbee
Mod Install Guides
...
Game Boy Advance (AGB)
📺 Display Mods

AGB IPS V2 with TV Output Hispeedido | Install Guide

13min

This is our guide for the HISPEEDIDO IPS V2 with TV Output options.

Video Guide



Getting Started

Required Tools:

  • Tweezers
  • J1 (Japanese Industrial standard) Screwdriver
  • Y1 Tri-point screwdriver
  • OEM GBA shell OR IPS Modified Shell

Take Inventory

Ensure you have all the included parts with the kit. See below:

  • IPS Backlit Screen
  • IPS Control PCB
  • 3M Adhesive
  • Two Ribbon Cables (one 32 pin, one 40 pin)
  • Centering Spacers
  • Five Pretinned Wires
  • Link port to A/V Cable

Before you proceed...

This kit requires the removal of the EM3 resistor located right under the link port. Please be advised that this will not allow you to use the link port as originally intended after this mod.

Installing your IPS kit, bending the ribbon cables, soldering, or applying any adhesives in this kit will void the warranty and return policy. Fully test your kit before proceeding.

Dry Testing

Check our dry testing guide located here for more specific instructions.

Successful Dry Test
Successful Dry Test


Install Guide

To begin installing this kit, we will first remove the EM3 resistor from right below the link port. This will allow the video to be output through the link port.

Before removal
Before removal

After removal
After removal


Next we will solder the three wires for the normal brightness control

Document image


Now we will solder the last two points for the A/V out.

Back Side Solder Points
Back Side Solder Points


Once soldered, preform one more test to ensure all the buttons work to adjust brightness.

Successfull Button Test
Successfull Button Test


Start/Select Area Trim

See our list of shell trimming guides as this step may vary depending on which shell you're using!

We are continually updating and adding guides to this section. For assistance, reach out to us at support@handheldlegend.com

Even with pre-cut shells, we recommend carefully examining the Start/Select area and trimming as needed. The PCB extends out past the IPS display by a milimeter or less, it can slightly vary.

See the diagram below for an example of how much you'll need to trim.



Document image




Ensure the screen is fitted into the bottom right hand side of the screen window. We recommend placing the touch sensors in these areas to allow for easy access.

This shell was premodified slightly, hence the spacer.
This shell was premodified slightly, hence the spacer.


Test and Reassemble

Ensure all the buttons are working, and that the TV out function works

Document image


Now press select and both shoulder buttons for five seconds to switch to TV mode

Document image


If everything is functioning as expected, go ahead and complete the reassembly by replacing the rear screws. See our disassembly guide if you need further assistance here.

Troubleshooting

  • If your AV cable is not working, this may be due to a cable mix-up from the supplier. This can be resolved by swapping the pin soldered for AV out. Instead of soldering "AV" on the PCB to Pin 1, solder it to Pin 3.
Document image

  • IPS Troubleshoot Guide.
  • If you have any questions or concerns, please reach out to support@handheldlegend.com



Updated 05 Dec 2023
Did this page help you?
PREVIOUS
AGB IPS V2 (Touch Sensor Version) Hispeedido | Install Guide
NEXT
AGB IPS Cloud Version | Install Guide
Docs powered by Archbee
TABLE OF CONTENTS
Video Guide
Getting Started
Take Inventory
Dry Testing
Install Guide
Start/Select Area Trim
Test and Reassemble
Troubleshooting
Docs powered by Archbee